How do you replace a clawfoot tub drain?

How To Install a Clawfoot Tub – YouTube

How do you replace an old bathtub drain?

How to Replace a Tub Drain | Ask This Old House – YouTube

What size is the drain on a clawfoot tub?

Antique bathtubs, such as historic clawfoot tubs, sometimes have slightly smaller drain openings, often 1 3/8 inches in diameter. These drains can still be connected to a standard 1 1/2-inch drain pipe by using a reducing washer to make the connection.

How do you remove a cast iron tub drain?

How to Remove a Cast Iron Tub Directions

  1. Shut off the water supply to the tub.
  2. Open tub faucet to drain water remaining in supply lines.
  3. Remove screws securing the plate covering the overflow assembly.
  4. Work loose the lever hook and take it out.
  5. Take out the drain stopper.

How do you remove the plug from a clawfoot tub?

How to Remove any Bathtub Stopper, Pop-up, Grate, or Plug – YouTube

How do you remove a bathtub drain without the tool?

Tub Drain Removal without a Special Tool – YouTube

Are all tub drains the same size?

Thanks to the standardization, any bathtub drain can fit any standard bathtub between 14 and 26 inches in depth. The size of the drain is standardized because it needs to fit to the P-trap, which is the next component of the drain.

How do you install a clawfoot tub drain?

How To Install a Clawfoot Tub – YouTube

How do I know what size tub drain I need?

Measure from the piping section where it branches out toward the drain over to the drain hole and write that horizontal distance measurement down. That will give you the length and width that is needed for your drain. Your local hardware or home improvement store should carry a bathtub drain that fits your needs.

How do clawfoot bathtubs drain?

Source and drain lines come through the floor.

In a typical clawfoot tub installation, both the water source pipes and the drain pipe enter the bathroom through the floor. … Consult with a licensed plumber if you intend to install a clawfoot tub on the second floor of your home!

How much does it cost to remove a cast iron bathtub?

Cast Iron Tub Removal Cost. To remove a standard cast iron tub, you can expect to pay anywhere from $255-$395. Based on where the tub is location in the home or on the property, your cost could be more.

How do I know if my tub is steel or cast iron?

1) Remove the overflow cover and popup lever from the head end of the tub and look at the edge of the hole. You should see black cast iron or bright steel. Also, if you remove the overflow cover, the material between it and the plumbing will be about 1/4 ” thick if it is cast iron. 1/16″ if it is steel.

How do you replace a cast iron tub?

How to Remove a Cast Iron Bathtub – YouTube

How do you remove a push pull drain stopper?

How to Remove a Push-Pull Drain Stopper:

  1. Set the drain to its open position.
  2. Lift up on the drain stopper’s knob and turn it counterclockwise.
  3. After enough turns, the drain stopper should be unscrewed and come free from the drain opening.

How do you remove a stuck pop up tub drain?

How to Remove Pop Up Tub Stopper. Easy Method! – YouTube

How do you remove a screw from a bathtub drain plug?

Most-Common Bathtub Stopper Removal Techniques – Visit

How do you remove a bathtub drain flange without the tool?

How to remove bathtub drain with broken cross members – YouTube

How do I remove a bathtub drain flange?

How to remove and replace a bath drain – YouTube

How do I unscrew a shower drain without tools?

How to Remove a Pop Up Bathtub Drain Plug Stopper | No Screws or …

How do you install a bathtub drain in a concrete slab?

How to Install a Bathtub in Basement Bathrooms — by Home Repair Tutor

Are tub drains universal?

Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep. They are this size because they must fit the opening of the P-trap — also 1 1/2 inches wide — which is a special pipe that has a sharp bend in it.

Are tub drain locations standard?

The position of the tub drain will vary, depending on the size and design of the tub, and you’ll need to cut an access hole in the floor at the drain end of the tub to allow for positioning and installing the drain line. This hole should be 9 inches wide and extend at least 12 inches from the wall.

How do you install a freestanding tub drain?

Easy Freestanding Tub Installation – WHY YOU NEED THIS!!!

How do you replace a clawfoot tub with a shower?

How to Add a Shower to a Claw-Foot Tub | Ask This Old House – YouTube

How much does it cost to install a clawfoot tub?

The national average cost range is $2,300 to $4,100 for an installed clawfoot tub. Most homeowners pay $2,850 for an installed cast iron, roll top tub.

Clawfoot Tub Installation Cost.

Clawfoot Tub Prices
National average cost $2,850
Average range $2,300-$4,100
Minimum cost $900
Maximum cost $5,800

What is a tub shoe?

The tub drain shoe is an elbow that channels water down the drain pipe, it is the first fitting attached to the bottom of the tub’s drain basket. In order to remove and replace the shoe you need to access beneath the bathtub.

How far is a bathtub drain from the wall?

Bathtub Drain Measurements

The drain hole should be a minimum of 12 inches away from the wall and 9 inches in scope. To rough in the drain, use a 1.5-inch pipe.

Does a clawfoot tub add value to a home?

According to the RealEstate.com survey, starter homes with claw-foot tubs sold for nearly 30% more than expected. Coffered ceilings also helped homes sell for 30% more than expected, and farmhouse sinks (thanks Joanna Gaines) helped homes sell for 26% more than expected.

How heavy is a cast iron clawfoot tub?

How heavy is a clawfoot tub? All bathtubs are heavy, but clawfoot tubs tend to be especially heavy – particularly the cast-iron models. A cast-iron tub can easily weight 200-400 pounds while empty – fill it with water and climb in and you’re looking at several hundred pounds of weight.

How do you refinish a clawfoot tub?

How to Refinish a Claw-Foot Tub | This Old House – YouTube

How long does it take to remove a cast iron tub?

For this step, you will need several screwdrivers, a small saw or keyhole saw. This step will usually take around 3-4 hours, depending on the size of your bathroom, so be prepared.

Can you cut a cast iron tub with a Sawzall?

The easiest and most versatile saw for this type of cutting is the reciprocating saw or “sawzall”. Blades are available up to nearly a foot in length, making it easy to cut most anything. Just don’t cut through the floor or your plumbing! Start with two cuts across the width of the tub, dividing the tub into thirds.

How much does it cost to remove a tub and install a walk in shower?

The installation and costs of converting a tub into a walk-in shower range between $5,997 and $11,950, with average coming in at $7,997. Although it may seem like a wide range for a simple project, many other factors contribute to the total cost.

What does a cast iron tub look like?

A cast iron tub will sound like a deep gong, just as if you hit a cast iron frying pan. Look at the bottom of the tub if possible. A cast iron tub will be black, and a steel tub will be metallic, although it may be covered with a layer of paint. An acrylic tub will look like coated plastic.

Can you resurface a cast iron bathtub?

Refinishing may be the most practical way of restoring a built-in bathtub, but for those lucky enough to have a removable claw-foot tub or cast-iron sink, the dream has long been to give it a new finish that matches the hardness and durability of the old one.

How can you tell how old a clawfoot tub is?

Next to the manufacturer’s name or the “Made in U.S.A.” logo, you often find the date of manufacture in the month/year format. For example, the numbers 12 31 state the manufacture date as December 1931. You might also see another number, such as 5 1/2. This number states the length of the tub in feet.

What holds a cast iron tub in place?

Bathroom Remodel 55 – Cast Iron Tub Installation – YouTube

How do you remove enamel from a cast iron tub?

Strip the surface enamel layer from your tub with chemical paint remover and a little bit of scrubbing. Once bathtubs that were originally finished with a porcelain enamel glaze become chipped, professionals had to treat the tub with acidic chemicals to refinish the tub.